Search found 29 matches
- Thu Jan 24, 2013 6:19 am
- Forum: CNC Shark Pro Plus HD
- Topic: Lubrication On Y Axis
- Replies: 10
- Views: 7778
Re: Lubrication On Y Axis
Thats where I get mine. I got both, the spray can, and a bottle of it..
- Thu Jan 24, 2013 6:17 am
- Forum: CNC Shark
- Topic: Touch Probe problem (wavy STL output)
- Replies: 3
- Views: 3145
Re: Touch Probe problem (wavy STL output)
I read somewhere that there was a break-in for this probe. It took me 3 times before the darn thing started doing what it was supposed to..
- Thu Jan 24, 2013 6:05 am
- Forum: CNC Shark Pro Plus HD
- Topic: X Axis Is Traveling
- Replies: 12
- Views: 7830
Re: X Axis Is Traveling
I will have to check the coupling today. One of the screws are kind of hard to get at. Is there any way to get at it without cutting an Allen wrench to get in there on the X axis coupling? I don't cut aggressively. .70 cut with a .070 stepover, and thats if it's a sharp endmill bit. And yes, the x z...
- Wed Jan 23, 2013 12:31 pm
- Forum: CNC Shark Pro Plus HD
- Topic: X Axis Is Traveling
- Replies: 12
- Views: 7830
X Axis Is Traveling
Has anyone noticed at all if their X axis is traveling at all. I will verify my X,Y home location after cutting a segment of my job, and have noticed that the X axis is traveling. For instance, the job that's in my shark right now has an X axis that is .064 off. Using a lazer pointer, checking the p...
- Fri Jan 11, 2013 4:22 pm
- Forum: Software. Programming
- Topic: xbox controller
- Replies: 5
- Views: 4690
Re: xbox controller
I sure would like to hear more about the wireless keypad..Please input .
- Fri Jan 11, 2013 4:20 pm
- Forum: Software. Programming
- Topic: Pausing/stopping the router
- Replies: 21
- Views: 14702
Re: Pausing/stopping the router
I normally run the code till I can't do it anymore, and just keep track of the line number I pause it on and write er down. Then do the E-STOP keypad click. I go into notepad the next day and find the line number I am looking for by clicking VIEW and then make sure STATUS BAR is selected. That way t...
- Fri Jan 11, 2013 4:02 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Essential Mill Set Components
- Replies: 1
- Views: 2182
Re: Essential Mill Set Components
All I have been using are 1/4" and 1/8". Although today, I should have used a larger end mill. I am so used to using a 1/4" I forgot. Don't forget what your radius corners are going to be. And what mills you are going to be able to get into them with. Kinda sucks when you may forget or overlook , an...
- Fri Jan 11, 2013 3:58 pm
- Forum: Shark Project File Sharing.
- Topic: Arts & Crafts Clip Art
- Replies: 4
- Views: 11423
Re: Arts & Crafts Clip Art
That topic has a rather wide range, maybe you can narrow it down a tad so I can help ya.
- Fri Jan 11, 2013 3:56 pm
- Forum: Software. Programming
- Topic: Smaller bit for section of 3d carving
- Replies: 1
- Views: 1846
Re: Smaller bit for section of 3d carving
What are you using for 3d software (Aspire)? Small example if I am not mistaken. Just for conversation here, I just opened up a file. It had a bunch of gingerbread men nested on it. I put a little rectangle on one of the men, and also made sure to click on the model, and voila, only what was in the ...
- Fri Jan 11, 2013 3:50 pm
- Forum: Software. Programming
- Topic: Gantry stops at line 33
- Replies: 3
- Views: 2446
Re: Gantry stops at line 33
I looked at your code. Didn't see anything wrong with it. Have you tried to re-start the control panel. In the mean time, if you figured out what was going on I would like to hear..pretty please. Have you tried to cut the code a bit and see if it still stalls on line 33?