I was half way through a job when the 10amp glass fuse blew out.
I replaced it with the spare, restarted the job, and, again about half way through it blew out again.
Any ideas as to why this is happening?
Any help would be appreciated.
Bob
Search found 12 matches
- Sat May 09, 2020 3:43 pm
- Forum: CNC Shark
- Topic: Fuse Blowing out
- Replies: 0
- Views: 2670
- Mon Sep 11, 2017 12:18 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Gantry does not stop
- Replies: 0
- Views: 3540
Gantry does not stop
Shark Pro HD3 V Carve Desktop Just recently, and not all the time, when I try to jog the router, either up or down on the Z axis, does not stop. I have to shut the control box off and restart it. The error message I get is; Access violation at address 00758162 in module cncsharkcp2.exe write of addr...
- Sun Sep 03, 2017 4:44 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Cedar Wood Issue
- Replies: 6
- Views: 6484
Re: Cedar Wood Issue
Sharkcutup I have no experience using fence boards, so I don't know if sanding them will help. It does take some time to work a smooth finish on the unfinished side. If you use both sides of a board, it would seem to be easier to buy with one side finished, cut your time in half. I use 1"x 8"x 8' or...
- Fri Sep 01, 2017 12:59 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Cedar Wood Issue
- Replies: 6
- Views: 6484
Re: Cedar Wood Issue
I make signs using nothing but Cedar. The Cedar is usually finished on one side. I have found that if you try to carve the unfinished side it will splinter & fray. Also I have found, that usually, any cut deeper than 3/16 0.1875 will cause the problem you are having if you are using a round nosed bi...
- Mon Apr 25, 2016 2:33 pm
- Forum: CNC Shark
- Topic: Touch Plate
- Replies: 1
- Views: 1749
Touch Plate
I damaged the cord on my shark touch plate.
I have it patched for now, but I do not know how long that will last.
Is there somewhere I can buy a replacement cord?
I looked at Nextwaves site and did not see one there.
Thank You
Bob
I have it patched for now, but I do not know how long that will last.
Is there somewhere I can buy a replacement cord?
I looked at Nextwaves site and did not see one there.
Thank You
Bob
- Thu Mar 24, 2016 11:24 am
- Forum: CNC Shark Pro Plus HD
- Topic: Vertical Lettering
- Replies: 5
- Views: 5027
Re: Vertical Lettering
Sorry for the delay in responding.
Thank You! I really appreciate the help.
Bob
Thank You! I really appreciate the help.
Bob
- Mon Mar 14, 2016 2:10 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Vertical Lettering
- Replies: 5
- Views: 5027
Re: Vertical Lettering
Thank you, but I need the letters to read from top to bottom.
L
I T
K W
E O
T L
H I
I N
S E
S
If I do it like this, The letter will not line up.
Bob
L
I T
K W
E O
T L
H I
I N
S E
S
If I do it like this, The letter will not line up.
Bob
- Mon Mar 14, 2016 10:53 am
- Forum: CNC Shark Pro Plus HD
- Topic: Vertical Lettering
- Replies: 5
- Views: 5027
Vertical Lettering
I have a request for a sign that requires the lettering to be vertical.
I can not figure out how to do this.
any help would be appreciated.
Thank You
Bob
I can not figure out how to do this.
any help would be appreciated.
Thank You
Bob
- Tue Sep 08, 2015 2:07 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Bits
- Replies: 4
- Views: 3731
Re: Bits
Thank you for the help.
Bob
Bob
- Sat Sep 05, 2015 4:22 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Bits
- Replies: 4
- Views: 3731
Bits
Can anyone recommend a place to buy 1/8" round nose bits with a 1/4" shank
Thank You
Bob
Thank You
Bob