Search found 104 matches

by jimily
Fri Oct 30, 2015 5:35 pm
Forum: Show off your CNC Shark projects
Topic: star wars edge lit acrylic
Replies: 13
Views: 9359

Re: star wars edge lit acrylic

Hah awesome! I was just looking at darth vader heads to do one for a friend. That looks really good.

Jim
by jimily
Fri Oct 30, 2015 5:32 pm
Forum: Show off your CNC Shark projects
Topic: Paradise Clock
Replies: 4
Views: 3246

Re: Paradise Clock

Very nice all around, I like stuff that glows. :)

Jim
by jimily
Tue Oct 27, 2015 1:27 pm
Forum: CNC Shark
Topic: controller software questioned
Replies: 12
Views: 7690

Re: controller software questioned

Yep, they will send it pretty quickly and then you have to go through the Control Panel install, and the registration of the controller box and you will be set, unless you have a probe and a touchplate, then you would also register those too. All instructions re on the NWA/Vectic sites too for easy ...
by jimily
Mon Oct 26, 2015 8:14 am
Forum: Show off your CNC Shark projects
Topic: Giant Jenga
Replies: 4
Views: 3422

Re: Giant Jenga

Ok good, I'll go hunt for some.
Thanks!
Jim
by jimily
Fri Oct 23, 2015 6:54 pm
Forum: Show off your CNC Shark projects
Topic: Memorial Night light
Replies: 7
Views: 4036

Re: Memorial Night light

That was very nice of you and it turned out really well. Thanks for the run-facts. :)

Jim
by jimily
Fri Oct 23, 2015 6:51 pm
Forum: Show off your CNC Shark projects
Topic: Giant Jenga
Replies: 4
Views: 3422

Re: Giant Jenga

Good stuffs, losing at that jenga game could cause a concussion!

Where you do get your brass plates?

Jim
by jimily
Wed Oct 21, 2015 1:00 pm
Forum: CNC Shark Pro Plus HD
Topic: Replacement Back Plate?
Replies: 19
Views: 11380

Re: Replacement Back Plate?

contd' And after it was over: IMG_1323.JPG The same length screws did not protrude through the front, close but no: IMG_1324.JPG The screw sizes reported by NWA are as follows: 4- 1/4-20 1 1/4 T27 bolts 4- 2 1/2 Phillips Flat machine screw 3- 3mm M5-50 Phillips Flat ms All in all it was way simpler ...
by jimily
Wed Oct 21, 2015 12:49 pm
Forum: CNC Shark Pro Plus HD
Topic: Replacement Back Plate?
Replies: 19
Views: 11380

Re: Replacement Back Plate?

Ok I got em. Needle nose pliers did the trick (I tried using the flat screwdriver before I asked and it was starting to chew the plastic, being a bruiser I thought to stop and ask doh!) Other than that initial hiccup it went so fast I didn't get many pictures. In the box: IMG_1319.JPG The right befo...
by jimily
Wed Oct 21, 2015 10:10 am
Forum: CNC Shark Pro Plus HD
Topic: PC re quirements
Replies: 8
Views: 5353

Re: PC re quirements

This page: http://www.vectric.com/products/vcarve/features.htm#tlimits makes me think it's in all the Vcarve apps, but are limited to cut size by the software in general on not Pro platforms. I have Pro 8 so I can't say what non-pro versions really have. Someone will know. Anyway Vectric.com is wher...
by jimily
Wed Oct 21, 2015 7:36 am
Forum: Software. Programming
Topic: Taptastic organization
Replies: 7
Views: 5888

Re: Taptastic organization

Yes now is when I need to start this kind of organization. I wish I were more innately organized but alas it is a struggle.

Thank you, there are some good tips here I can use.

Thanks again,
Jim