Search found 13 matches
- Wed Oct 25, 2017 2:17 pm
- Forum: Setting up the Shark
- Topic: Y Axis Set Screw
- Replies: 1
- Views: 3301
Y Axis Set Screw
Looks like my Y-axis set screw came loose on HD4. Anything I should know or precautions I should take before I re-tighten it? I read another post about taking the deck off and creating an access hole, but not ready to go to that extreme.
- Mon Jul 17, 2017 8:42 am
- Forum: Software. Programming
- Topic: Virtual Zero
- Replies: 4
- Views: 4813
Re: Virtual Zero
I just made a discovery while looking over the manual. Looks like if I use the pendant to set virtual zero (instead of following the prompts on my laptop), I will have the option to use existing points. As I load each tool path into the CNC program on my laptop, it asks me if I want to use virtual z...
- Sun Jul 16, 2017 4:11 pm
- Forum: Software. Programming
- Topic: Virtual Zero
- Replies: 4
- Views: 4813
Re: Virtual Zero
It will ask you if you like to used the last VZ settings and you answer accordingly. If you did not change bits your z will still be set. if you are carving on a pocketed area your new tool path should have new start point (minus the amount you just took out of that area) this is done in the text o...
- Thu Jul 13, 2017 9:07 pm
- Forum: Software. Programming
- Topic: Virtual Zero
- Replies: 4
- Views: 4813
Virtual Zero
If I want to use virtual zero on a project, do I have to collect the five data points every time I run a new tool path? Is there a way to collect and store the virtual zero information for the project so that I can recall it for the next tool path?
- Mon Jun 12, 2017 2:49 pm
- Forum: Setting up the Shark
- Topic: Receptacle on Pendant for ... what?
- Replies: 2
- Views: 3160
Re: Receptacle on Pendant for ... what?
For anyone who may be interested, I talked to John with NWA tech support. He said that the jack on the pendant can be used for the touch plate but not the probe. The jack on the front of the controller can be used for either touch plate or probe.
- Mon Jun 12, 2017 2:45 pm
- Forum: Setting up the Shark
- Topic: Apps>Touch Plate Calibration vs "Plate"
- Replies: 1
- Views: 2468
Re: Apps>Touch Plate Calibration vs "Plate"
For anyone who may be interested, I talked to John with NWA tech support. He said that there's essentially no difference. Apps>Touch Plate Calibration and the Plate button on the pendant perform the same function.
- Sat Jun 10, 2017 2:08 pm
- Forum: Setting up the Shark
- Topic: Apps>Touch Plate Calibration vs "Plate"
- Replies: 1
- Views: 2468
Apps>Touch Plate Calibration vs "Plate"
I followed the instructions in the Touch Plate Manual using Apps>Touch Plate Calibration on the pendant. But on the home screen of the pendant on the right hand side, there's a button for "Plate" which appears to take me to the same procedure. I suppose the "Plate" button could be routinely used onc...
- Sat Jun 10, 2017 1:48 pm
- Forum: Setting up the Shark
- Topic: Receptacle on Pendant for ... what?
- Replies: 2
- Views: 3160
Receptacle on Pendant for ... what?
There's a jack receptacle on the controller for the touch plate or touch probe. What is the jack receptacle on the side of the pendant used for? Can the touch plate or the touch probe be plugged into it instead of the controller? Seems like I tried it and it didn't work.
- Sat Jun 10, 2017 1:41 pm
- Forum: Setting up the Shark
- Topic: Gantry Height
- Replies: 5
- Views: 5021
Re: Gantry Height
I figured out my confusion. The assembly instructions in the Owner's Manual say to use the "bottom" three sets of holes for standard operation (which would put the gantry in its highest position by my interpretation.) I later noticed that the assembly instructions in the 4-page Quick-Start Guide say...
- Fri Jun 09, 2017 9:09 am
- Forum: Setting up the Shark
- Topic: New Shark doesn't power up
- Replies: 7
- Views: 6236
Re: New Shark doesn't power up
Problem solved! Where in the instructions does it say that the emergency shut off button is shipped in the off position...or does everybody but me know that . Thanks, Bob!