Search found 18 matches
- Sun May 14, 2017 5:00 pm
- Forum: CNC Shark
- Topic: Control Panel v2.1 Build 25f Virtual Zero
- Replies: 14
- Views: 11923
Re: Control Panel v2.1 Build 25f Virtual Zero
Here is an update. I was working with Joseph at Nextwave. I know he has posted on the forum. After some trial and error we were able to get everything working for what I needed it to do. They are working on the new 3.0 software. The last version that I have is Build25i and I've been using it for abo...
- Fri Apr 07, 2017 3:40 pm
- Forum: CNC Shark
- Topic: Control Panel v2.1 Build 25f Virtual Zero
- Replies: 14
- Views: 11923
Re: Control Panel v2.1 Build 25f Virtual Zero
Ok here is where I’m at. Not heard from Nextwave all week. I first emailed them on Sunday. Just emailed them again I know I won’t hear back from them until next week. Never had trouble getting information from them before. Not sure what the hold up is now. Today I needed to run some signs that take ...
- Wed Apr 05, 2017 2:57 pm
- Forum: CNC Shark
- Topic: Control Panel v2.1 Build 25f Virtual Zero
- Replies: 14
- Views: 11923
Re: Control Panel v2.1 Build 25f Virtual Zero
Update
Still not heard for Nextwave
I made a short YouTube video of the problem I'm have with the new CNC Shark Build 25f.
Here is the link. Sorry not real good at videos. Hopefully the link works.
https://youtu.be/pgBH5xlFQwQ
Tim
Still not heard for Nextwave
I made a short YouTube video of the problem I'm have with the new CNC Shark Build 25f.
Here is the link. Sorry not real good at videos. Hopefully the link works.
https://youtu.be/pgBH5xlFQwQ
Tim
- Mon Apr 03, 2017 12:28 pm
- Forum: CNC Shark
- Topic: Control Panel v2.1 Build 25f Virtual Zero
- Replies: 14
- Views: 11923
Re: Control Panel v2.1 Build 25f Virtual Zero
Here is an update: Not heard from Nextwave yet. Not sure what this is - Revised Virtual process. Only uses borders on X or Y axis if borders are less than 15% of span size. Ran some tests this morning. I have two Sharks. On the Shark with the Build 25f material offset set to 1 Material size is 19" w...
- Sun Apr 02, 2017 6:04 pm
- Forum: CNC Shark
- Topic: Control Panel v2.1 Build 25f Virtual Zero
- Replies: 14
- Views: 11923
Re: Control Panel v2.1 Build 25f Virtual Zero
Here is the rest of the View Release Notes and post: I don't really see much difference form Build 22 Not sure what GUI is? [2.1] [xx] planned update : CommandStack... line added to reconnect to controller after disconnect, so system can break out of loop resulting from disconnect. requires more tes...
- Sun Apr 02, 2017 11:48 am
- Forum: CNC Shark
- Topic: Control Panel v2.1 Build 25f Virtual Zero
- Replies: 14
- Views: 11923
Re: Control Panel v2.1 Build 25f Virtual Zero
Here is the View Release Notes and post: It is a lot. The Shark runs and cuts ok. Also everything is set to inches. [2.1] [17] planned update : CommandStack... line added to reconnect to controller after disconnect, so system can break out of loop resulting from disconnect. [16] : Preferences update...
- Sat Apr 01, 2017 11:07 am
- Forum: CNC Shark
- Topic: Control Panel v2.1 Build 25f Virtual Zero
- Replies: 14
- Views: 11923
Control Panel v2.1 Build 25f Virtual Zero
Good morning, I just updated my control panel from v2.1 Build 22 to Build 25f. It's been a while since my last update. On the Build 22 when I run virtual zero I have it set to take the measurement 1" in from the corners from the edge of the material . With the Build 25f it goes all the way to the co...
- Fri Dec 11, 2015 7:31 pm
- Forum: CNC Shark
- Topic: New Touch plate cable
- Replies: 5
- Views: 3593
Re: New Touch plate cable
Thank you all for the information. When I looked on Next Wave a couldn't find the touch plate cable. Thanks for the link. My son is an electrician and he found that somewhere in the twisted wire area a wire must be broke. We cut the wire at the two plug ends and rewired with new wire and we are back...
- Thu Dec 10, 2015 10:03 am
- Forum: CNC Shark
- Topic: New Touch plate cable
- Replies: 5
- Views: 3593
New Touch plate cable
Good morning everyone, Does anyone know where to purchase a new touch plate cable, besides right from Next Wave? My cable got broken and can no longer be repaired so I am looking for a replacement cable and I can't get through to Next Wave. I know they are busy because of the holidays so I am lookin...
- Fri Mar 28, 2014 10:43 am
- Forum: CNC Shark
- Topic: Different run times Shark Pro vs Shark Pro Plus HD
- Replies: 16
- Views: 6684
Re: Different run times Shark Pro vs Shark Pro Plus HD
Update to my problem of run time
Next Ware found that my control box settings were not set right. They had me reset them and now my run time is the same as my Shark Pro.
I want to thank Next Wave for taking the time to solve the issue.
Tim
Next Ware found that my control box settings were not set right. They had me reset them and now my run time is the same as my Shark Pro.
I want to thank Next Wave for taking the time to solve the issue.
Tim