Search found 1368 matches
- Mon Dec 26, 2016 10:06 am
- Forum: CNC Shark
- Topic: CNC Shark accuracy is off
- Replies: 14
- Views: 9161
Re: CNC Shark accuracy is off
Well - the box test mentioned above is a good check for the x and y travel. If you find you're out of square with this test, I'd again just gently push the gantry or the motor carriage (depending on the axis you are testing), and see if there is any noticeable movement. If there is, you can tighten ...
- Mon Dec 26, 2016 8:30 am
- Forum: CNC Shark
- Topic: CNC Shark accuracy is off
- Replies: 14
- Views: 9161
Re: CNC Shark accuracy is off
You don't say - but after the slam and drag incident - did you check the system overall for any slop in any of the directions of travel? Also, after this, and even after you swap out the spoil boards, have you checked the angle of the rout to the spoil board - is it perpendicular from different angl...
- Wed Dec 07, 2016 11:40 am
- Forum: CNC Shark
- Topic: Vectric 12 Days of Christmas
- Replies: 0
- Views: 3390
Vectric 12 Days of Christmas
An annual gift from Vectric - free 3D models. If you're not aware of this - here's the link - a new one every day. It does appear that previous day's models are still available for download as well.
http://www.vectric.com/vectric-12-days-of-christmas/
http://www.vectric.com/vectric-12-days-of-christmas/
- Wed Oct 12, 2016 8:07 am
- Forum: Show off your CNC Shark projects
- Topic: What I did this summer...
- Replies: 6
- Views: 5142
Re: What I did this summer...
That is awesome! Always appreciate your projects and insight Bob. Thanks for sharing this.
- Sat Sep 24, 2016 8:41 am
- Forum: Show off your CNC Shark projects
- Topic: Sundial
- Replies: 7
- Views: 8166
Re: Sundial
Really interesting project Bill - and appreciate how you've added a lot of visual components to the design. Does seem a little quiet, but as you note, a lot of looking (and probably note taking). Thanks for sharing your work!
- Mon Sep 12, 2016 6:34 am
- Forum: CNC Shark
- Topic: Vcarve Letters
- Replies: 3
- Views: 3442
Re: Vcarve Letters
I'm not sure I understand the question well enough to comment - can you attach a picture of what you want to achieve?
- Sun Sep 11, 2016 6:38 pm
- Forum: CNC Shark
- Topic: Multiple engraved layers on a wood sign.
- Replies: 3
- Views: 3126
Re: Multiple engraved layers on a wood sign.
This post may have some answers for you - http://cncsharktalk.com/viewtopic.php?f ... 544#p26544
- Tue Aug 23, 2016 9:52 pm
- Forum: CNC Shark
- Topic: Multiple Pass - Issues
- Replies: 7
- Views: 4424
Re: Multiple Pass - Issues
When you say 'multiple passes' - is this multiple passes, but all coming from the same toolpath? Not that it should matter - but a potential problem if 2 separate toolpaths. What toolpath speed are you using for these 2 passes? What is the bit and what is the per pass cutting depth? I'd also try run...
- Mon Aug 22, 2016 9:54 pm
- Forum: CNC Shark Pro Plus HD
- Topic: "Jumps" in cut pattern
- Replies: 6
- Views: 5277
Re: "Jumps" in cut pattern
Hi Jim, If you haven't already - I'd also look at all the vertices and use the Smooth command on them. If they are just 'points' then the toolpath will try to go to them and then to the 'next' one. You could select all of the vertices along the edges of the legs (while in node editing mode) and tap ...
- Thu Aug 18, 2016 6:28 am
- Forum: Shark Pro Plus
- Topic: CNC Shark Pro Plus Machining errors
- Replies: 8
- Views: 9348
Re: CNC Shark Pro Plus Machining errors
I'd contact support. You're going to end up going through some troubleshooting steps again - but you may have a defective control box and NWA pretty good about service.