Struggling with dust collection setup

Questions/answers/discussion about initial setup of your CNC Shark

Moderators: sbk, al wolford

Post Reply
John2015
Posts: 3
Joined: Thu Feb 26, 2015 3:39 pm

Struggling with dust collection setup

Post by John2015 »

Hello,

I'm considering buying a CNC Shark SD120. I will be using it in my basement, so I need effective dust collection without an expensive setup. I would prefer to use a vacuum that pulls chips and sawdust right from the tip of my routing bit, instead of building an enclosure and trying to evacuate that enclosure. I've found two products that look promising:

https://www.rockler.com/dust-right-flex ... -4QAvD_BwE

https://www.amazon.com/Loc-Line-80813-S ... 832ad4b4d7

I would like some input about these two products as well as any additional suggestions about other similar products.

Thanks in advance.

SteveM
Posts: 167
Joined: Thu Sep 08, 2016 1:29 pm
Location: Franklin, Wisconsin

Re: Struggling with dust collection setup

Post by SteveM »

I would use a Oneida Dust Deputy with a shop vac. It will work just fine for you.
You could either use a 5 gal bucket with a lid or something larger that won't have to be emptied as ofte n.

OCEdesigns
Posts: 102
Joined: Fri Jan 11, 2019 8:26 am

Re: Struggling with dust collection setup

Post by OCEdesigns »

I use the dust deputy and I'm very happy. It collects even the fine dust from my belt sander!
Shark HD4 Extended Bed, Water Cooled Spindle. VCarve Pro 9.5

markjonesranger
Posts: 1
Joined: Mon Aug 17, 2020 3:47 pm

Re: Struggling with dust collection setup

Post by markjonesranger »

I just bought a Shark about 3 weeks ago. After about 15 projects My shop is getting covered by fine dust and I am using the factory dust collection shoe. Yesterday I started to build a enclosure for it. Using 1" thick Blue foam board as the box. It will fit over the top of the shark it only weighs a few pounds. I have a genair fan that I will use to pull the air out of the enclousure and send it to the dust deputy. I Used fine thread dry wall screws and gorilla glue for foam (must wet both surfaces when you glue it to activate it). It's curing out in the garage now. (It will take 2 weeks to get that glue off of my fingers) (I made a 4 station paint booth using this same design and assembly and it lasted for many years with a bunch of Royal Rangers (church scouts) painting their projects in it. It vented outside.) (Also made a 12 compartment air drying box for Ranger Derby cars using the same stuff and assembly kind of like a easy bake oven for Pinewood Derby and small paint projects...we would have 50 kids building and painting cars sometimes.)
I don't spend a lot of time watching the Shark Cut. I am thinking of putting a buzzer on the router when it shuts off so I will know when to change the next bit.

I am really enjoying this tool. Except for the dust and the loud noise it's fun. I am using head phones and getting caught back up on some old songs but my neighbors and family will appreciate a 20% reduction in noise. I cut out ten round boxes last few days that have self centering lids with our Royal Ranger Emblems carved in them and they boys names carved in them all out of red oak. They came out nice. Gifts for joining our Frontiersman Membership. They can put their flint and steel and char cloth in these.

User avatar
Kayvon
Posts: 454
Joined: Tue Oct 21, 2014 11:46 pm

Re: Struggling with dust collection setup

Post by Kayvon »

Is it possible to add a smoke detector inside the enclosure, or will the dust trigger it constantly? It would be nice to have an indication of fire before everything is melted and the fire is out of control.

User avatar
Bob
Posts: 1148
Joined: Sun Aug 08, 2010 3:35 pm

Re: Struggling with dust collection setup

Post by Bob »

"Is it possible to add a smoke detector inside the enclosure, or will the dust trigger it constantly? It would be nice to have an indication of fire before everything is melted and the fire is out of control."
This is a huge topic of concern for me. I have tried several types of detectors in my shop, with no success. Either over-spray from finishing, or dust triggers the alarm. I would like to know what has been tried successfully by others.
Bob

Post Reply