I think I followed all the steps still cannot get the file to run.
Search found 30 matches
- Mon Dec 09, 2019 5:29 pm
- Forum: CNC Shark
- Topic: laser attachment
- Replies: 3
- Views: 3376
- Sun Dec 08, 2019 5:55 pm
- Forum: CNC Shark
- Topic: laser attachment
- Replies: 3
- Views: 3376
laser attachment
I recently bought the laser and all needed accessories to convert my controller. I tried running a test path and nothing happened except the Z axis went up and down . The controller just went back to the run screen after the router went up in down in the Z axis and the laser did not come on. I am ru...
- Tue Feb 12, 2019 10:02 pm
- Forum: Software. Programming
- Topic: Cutting a 3d model
- Replies: 2
- Views: 2725
Cutting a 3d model
I have never cut a 3d model before and need some advice. How do I cut this. Need it about 7 or 8 inches long.
- Mon Feb 11, 2019 10:28 pm
- Forum: Shark Project File Sharing.
- Topic: 3d hand
- Replies: 1
- Views: 5384
3d hand
Looking for a 3d hand. I am running vcarve and cut 3d. Looking for something that I could cut both sides front and back of hand.
- Mon May 25, 2015 7:49 am
- Forum: Show off your CNC Shark projects
- Topic: 3d plaque gift for my niece
- Replies: 5
- Views: 3665
Re: 3d plaque gift for my niece
Thanks guys. Still learning how to get lettering done and smooth finis. Enjoyed doing it for her and am proud of her.
Bud
Bud
- Thu May 21, 2015 1:14 am
- Forum: Show off your CNC Shark projects
- Topic: any ideas on how to fix this
- Replies: 9
- Views: 5596
Re: any ideas on how to fix this
Thanks 4D will take a look at it and give it another go.
Can you do this on lithophanes that were created in photo vcarve and imported into vcarve 8 ?
Bud
Can you do this on lithophanes that were created in photo vcarve and imported into vcarve 8 ?
Bud
- Tue May 19, 2015 11:11 pm
- Forum: Show off your CNC Shark projects
- Topic: any ideas on how to fix this
- Replies: 9
- Views: 5596
Re: any ideas on how to fix this
Hope this what you were wanting?
1/4" ball nose 50 ipm roughing tp
1/8" tapered ball nose 25 ipm finish tp
1/4" end mill 50 ipm used for profile cut out
9/16" 90 degree v-bit 100 ipm used for lettering and chamfer
And thanks for looking at it Roger.
Bud
1/4" ball nose 50 ipm roughing tp
1/8" tapered ball nose 25 ipm finish tp
1/4" end mill 50 ipm used for profile cut out
9/16" 90 degree v-bit 100 ipm used for lettering and chamfer
And thanks for looking at it Roger.
Bud
- Tue May 19, 2015 3:10 am
- Forum: Show off your CNC Shark projects
- Topic: any ideas on how to fix this
- Replies: 9
- Views: 5596
Re: any ideas on how to fix this
Thanks Roger. Will try and figure out how to post the crv file. May take me a day or so as I am working 12 hour shifts at night. The feed rate was 100 ipm or less I'm pretty sure 1/4" ball nose for the rough tool path and 1/8" tapered ball nose for the finish tool path feed rate was 50 ipm I belive....
- Mon May 18, 2015 8:36 pm
- Forum: Show off your CNC Shark projects
- Topic: any ideas on how to fix this
- Replies: 9
- Views: 5596
any ideas on how to fix this
When doing the plaque for my niece and on the lithophanes I have done I have this issue around the edges.
The bit cuts into the sides on each pass. On the plaque alot of sanding took care of it. Is there anyway to stop this from happening or clean it up with the shark?
Bud
The bit cuts into the sides on each pass. On the plaque alot of sanding took care of it. Is there anyway to stop this from happening or clean it up with the shark?
Bud
- Mon May 18, 2015 8:30 pm
- Forum: Show off your CNC Shark projects
- Topic: Finally doing acrylic
- Replies: 12
- Views: 7321
Re: Finally doing acrylic
Nice work. Want to try my hand at that one day.