Search found 10 matches
- Fri Nov 13, 2015 4:50 pm
- Forum: Show off your CNC Shark projects
- Topic: Toy cars and stuff
- Replies: 2
- Views: 2328
- Fri Nov 13, 2015 4:46 pm
- Forum: Show off your CNC Shark projects
- Topic: Toy cars and stuff
- Replies: 2
- Views: 2328
Toy cars and stuff
Here are a few things I have done.
- Wed Sep 30, 2015 4:29 pm
- Forum: CNC Shark
- Topic: Shark Piranha vs Piranha FX
- Replies: 10
- Views: 9142
Re: Shark Piranha vs Piranha FX
I asked Next Wave Automation if they would be making the laser avalable for the older Piranha and they told me that after they get their Kickstarter orders manufactured and shipping they were going to look at making an upgrade kit for the older modle
- Tue Aug 18, 2015 3:29 pm
- Forum: Setting up the Shark
- Topic: Gaps in inlays?
- Replies: 5
- Views: 5182
Re: Gaps in inlays?
The colt only goes down to 16,000 rpm.
I'll give that a try.
I'll give that a try.
- Mon Aug 17, 2015 1:23 pm
- Forum: CNC Shark
- Topic: dust collection
- Replies: 4
- Views: 3734
Re: dust collection
Mine is not so pretty but it works well. The front panel is on 270degree hinges so I can fold it all the way over and the sides open for cleaning. The controller is on a French cleat so I can pick it up and use it in hand. The machine is set on the edge of the cross supports so there is no way to ac...
- Mon Aug 17, 2015 12:58 pm
- Forum: Setting up the Shark
- Topic: Gaps in inlays?
- Replies: 5
- Views: 5182
Re: Gaps in inlays?
I am using a piranha with a Bosch Colt. I've only had it for a couple of months. I am using VCarve desktop 8.020 Inlay (male and female) tool path I am using a 1/8" end mill at feed rate 60 inches/min. I believe the router is set to it's highest speed which the literature claims is 35,000 rpm. 20 ip...
- Sun Aug 16, 2015 3:22 pm
- Forum: Setting up the Shark
- Topic: Gaps in inlays?
- Replies: 5
- Views: 5182
Gaps in inlays?
Is this what I should expect?
My inlays have gaps. Is this because i was using cheap wood?
My inlays have gaps. Is this because i was using cheap wood?
- Fri Aug 14, 2015 12:52 pm
- Forum: CNC Shark
- Topic: Piranha Issues
- Replies: 15
- Views: 9166
Re: Piranha Issues
I see the flat is also inside the dish around the horse. This would hint to me that it is not likely binding on an obstacle or cord. Mimbler's suggestion of material movement or driving it too hard (too fast) are good to check. I'd also suggest checking to see if the router is secure in the clamp or...
- Fri Jul 31, 2015 12:59 pm
- Forum: Software. Programming
- Topic: How to create a keyhole slot?
- Replies: 1
- Views: 2646
How to create a keyhole slot?
How can I create a keyhole slot.
I have searched the forums but all of the solutions seem to be "use the gadget". Unfortunately, I have Vcarve desktop and cannot afford to pay $350 to make a keyhole.
Are there any other options?
I have searched the forums but all of the solutions seem to be "use the gadget". Unfortunately, I have Vcarve desktop and cannot afford to pay $350 to make a keyhole.
Are there any other options?
- Fri Jul 31, 2015 10:30 am
- Forum: CNC Shark
- Topic: dust collection
- Replies: 4
- Views: 3734
Re: dust collection
I build an enclosure for my piranha with a vacuum port on the bottom and a vent on top.
Unfortunately my controller went out just as I finished the enclosure so I have not had a chance to use it yet.
Unfortunately my controller went out just as I finished the enclosure so I have not had a chance to use it yet.