Hi
Thr Shark control panel software will not display the touch plate button until you enter the regeristation code you receive from NWA. There is no trial period.
DickL
Search found 33 matches
- Sun Aug 19, 2012 8:21 am
- Forum: CNC Shark
- Topic: Trouble with touch plate
- Replies: 3
- Views: 2426
- Mon Aug 13, 2012 10:11 am
- Forum: Setting up the Shark
- Topic: x & y axis
- Replies: 24
- Views: 15748
Re: x & y axis
Hi
I have done it on my basic (13 X 24) Shark, but you also have to rotate the gantry or you will get a mirrow image.
There was a thread on the subject.
DickL
I have done it on my basic (13 X 24) Shark, but you also have to rotate the gantry or you will get a mirrow image.
There was a thread on the subject.
DickL
- Fri Aug 10, 2012 1:42 pm
- Forum: Shark Pro Plus
- Topic: What's the Next Feature You Would Like?
- Replies: 44
- Views: 35000
Re: What's the Next Feature You Would Like?
I vote for limit switches I've run my Z axis into the stops so many times that I think I should replace the T nut.
DickL
DickL
- Fri Aug 10, 2012 9:56 am
- Forum: Shark Pro Plus
- Topic: Touch Plate!
- Replies: 42
- Views: 41001
Re: Touch Plate!
I just finished my first project since installing my touch plate which arrived yesterday. Six bit changes and the touch plate worked every time. I received the key this morning and installed it in the control panel to activate the touch plate software module. I have the basic (13 X 24) shark which I...
- Wed Jun 20, 2012 8:10 pm
- Forum: Setting up the Shark
- Topic: computer hardware setup
- Replies: 6
- Views: 4634
Re: computer hardware setup
Hi Windows 7 supports dual monitors. I just bought a new machine. I put my old 17 inch monitor on it and bought a 23 inch monitor which is also connected. I put the Aspire menus on the 17 9nch monitor and display the model on the 23 inch monitor. It really works great when i'm tracing an image or wa...
- Sun Jun 17, 2012 12:18 pm
- Forum: Show off your CNC Shark projects
- Topic: My Parrots
- Replies: 3
- Views: 2857
Re: My Parrots
Hi
With Aspire, I have made 2 sided objects by cutting a top and bottom half and glueing them together. Cut3D will cut the top side then you flip the work piece to cut the bottom. You have to make sure the zero stays aligned when you flip the work piece to keep the top and bottom aligned.
DickL
With Aspire, I have made 2 sided objects by cutting a top and bottom half and glueing them together. Cut3D will cut the top side then you flip the work piece to cut the bottom. You have to make sure the zero stays aligned when you flip the work piece to keep the top and bottom aligned.
DickL
- Tue Jun 12, 2012 3:45 pm
- Forum: Show off your CNC Shark projects
- Topic: My Parrots
- Replies: 3
- Views: 2857
My Parrots
Hi
I modeled the parrot using Aspire and generated tool paths for both sides using Cut3D.
DickL
I modeled the parrot using Aspire and generated tool paths for both sides using Cut3D.
DickL
- Mon Jun 11, 2012 7:17 pm
- Forum: Setting up the Shark
- Topic: It just does not work :{
- Replies: 10
- Views: 6559
Re: It just does not work :{
If you have energency stop, is it set?
- Wed May 23, 2012 5:22 pm
- Forum: Shark Pro Plus
- Topic: Going well , but a question
- Replies: 8
- Views: 5326
Re: Going well , but a question
Your touch plate question went into the NWA black hole.We are only customers, we don't hane a need to know what happened to the touch plate that was due the first quarter.
Yes I am annoyed.
DickL
Yes I am annoyed.
DickL
- Mon May 07, 2012 2:07 pm
- Forum: CNC Shark
- Topic: Asking me to register AGAIN
- Replies: 18
- Views: 8502
Re: Asking me to register AGAIN
Hi We have a bit of a disconnect. On page 122, the computer running the control panel must still be connected to the shark. In your prievous post, you said the new version of the control panel would execute even if the shark were not connected, but all of the buttons would be greyed out. I would lik...