Search found 168 matches
- Mon Nov 28, 2016 10:33 pm
- Forum: CNC Shark
- Topic: HD4 pendant Problems
- Replies: 14
- Views: 12955
Re: HD4 pendant Problems
The pendant is connected to the control box by a cable. I just have to unhook it and bring it in the house so it stays warm. When I am in the shop, I have a heater to keep myself warm. When I am done for the day, I don't heat the shop. I don't think the cold hurts anything else. I don't think the co...
- Mon Nov 28, 2016 9:36 pm
- Forum: CNC Shark
- Topic: HD4 pendant Problems
- Replies: 14
- Views: 12955
Re: HD4 pendant Problems
From what I understand they are. When I talked with tech support, they were very helpful an d talked me thru on getting it to work again. The only problem is it has done it more than once, but now I know how to reset the pendant. They also told me to use a eraser on a pencil or a stylus instead of u...
- Mon Nov 28, 2016 3:33 pm
- Forum: CNC Shark
- Topic: HD4 pendant Problems
- Replies: 14
- Views: 12955
HD4 pendant Problems
I just got the new HD4. Used it 1 time and the color pendant has gone dead and has to be re calibrated. I called tech support and he told me to loosen the screws on the front of the pendant and put my finger on the center of the screen and turn the control box on. Then it takes you into calibrate mo...
- Tue Nov 22, 2016 10:29 pm
- Forum: Shark Project File Sharing.
- Topic: Wood Clamps. My Design.
- Replies: 27
- Views: 46320
Re: Wood Clamps. My Design.
so the surface tool path is cut before the pocket tool path.
I watched the milling process a few times ant figured that is what must be done.
Thanks for the help
I watched the milling process a few times ant figured that is what must be done.
Thanks for the help
- Mon Nov 21, 2016 11:43 pm
- Forum: CNC Shark
- Topic: Tell us where you're from map
- Replies: 617
- Views: 534560
Re: Tell us where you're from map
Steve M
Franklin, Wisconsin
Got a bad HD4, Next Wave had it more than I did so I returned it for a Axiom. Very solid machine in my opinion!
Franklin, Wisconsin
Got a bad HD4, Next Wave had it more than I did so I returned it for a Axiom. Very solid machine in my opinion!
- Sun Nov 20, 2016 10:15 pm
- Forum: Shark Project File Sharing.
- Topic: Wood Clamps. My Design.
- Replies: 27
- Views: 46320
Re: Wood Clamps. My Design.
May sound like a dumb question, but the surface tool path would eliminate the pocket path you cut to allow the hold down bolt to go thru, unless you are flipping the board over and running that tool path to make the stock thinner.
If I am not understanding it correctly, please advise me.
If I am not understanding it correctly, please advise me.
- Wed Nov 09, 2016 11:41 pm
- Forum: Setting up the Shark
- Topic: Any thoughts on CNC Shark HD4
- Replies: 10
- Views: 9204
Re: Any thoughts on CNC Shark HD4
I have been attending the Shark classes at my local Rockler store. They just got a HD4 in and from what I can see is the router mount is thicker and looks larger than the HD3 they also have in the store. The class members also took a look at the new Shark and commented it looks much stronger. I don'...
- Tue Nov 08, 2016 6:32 pm
- Forum: Setting up the Shark
- Topic: Any thoughts on CNC Shark HD4
- Replies: 10
- Views: 9204
Re: Any thoughts on CNC Shark HD4
I have been looking at this site for some time and this is my first post I just ordered a HD4 that I should have in about a week, so I am eager to learn all I can about the software and the machine. I know very little about the vetric software, but have been working on the trial software and watchin...