Took some time but there you go
Moderators: al wolford, sbk, Bob, Kayvon
Took some time but there you go
There you go finally got some project done (did a few but this is my first one that is 100% finish) some up some down but finally. I use for the frame some paduak, really nice wood a bit costly but still nice. The picture was from a C17 taking off from Kandahar airfield. It is 17 by 10.
-
- Posts: 584
- Joined: Sun Jan 15, 2012 6:46 pm
- Location: North Little Rock, Arkansas
Re: Took some time but there you go
17 by 10 is a large carving! How long did it take to carve? Very nice work, by the way.
Being retired is hard work. Spending way too much time in the shop these days. (And loving it).
Shark Pro Plus HD, Vcarve Pro, Photo V Carve, Cut 3D, scan probe.
Shark Pro Plus HD, Vcarve Pro, Photo V Carve, Cut 3D, scan probe.
Re: Took some time but there you go
Thanks, it took over 10 hrs but i just let it run at night and during the day I work on the frame.
Re: Took some time but there you go
Very nice. Picture was excellent for this. The sharp contrast allowed it to turn awesomely..... well ok, I guess you had a little something to do with it too LOL
Roger
Roger
CNC Shark HD ~ Control Panel 2.0 ~ Windows 7 & XP
Located in West Tennessee near the Tennessee River
http://www.eaglecarver4.com
Located in West Tennessee near the Tennessee River
http://www.eaglecarver4.com
Re: Took some time but there you go
Very nice, I gotta try that someday
Re: Took some time but there you go
Excellent work. Never did a large one like that. Keep it up, like to see more of your work. What did you use to light it?
Tony
Tony
Buffalo,NY
"What will matter is not what you bought but what you built; not what you got, but what you gave”
Aspire 12.010, photo vcarve, cut3D.cnc mako shark extended bed with the new upgraded HD 5 gantry with Led pendent.
"What will matter is not what you bought but what you built; not what you got, but what you gave”
Aspire 12.010, photo vcarve, cut3D.cnc mako shark extended bed with the new upgraded HD 5 gantry with Led pendent.
Re: Took some time but there you go
i bought some light at Costco they come in 1 foot section they are bright white. trying to get a good place to purchase some but none of them so far were as bright as the one i got from Costco. I was told 3k kelvin for heat they are 12v the only problem is i can't cut them so yes most of my work will be min 13 inches wide or high so i don't have a problem trying to fit the lights inside. And not sure about other Canadian but man we are being robe when it is time to buy some of those lights. .
Re: Took some time but there you go
Are you talking about led lights? I get led lights on eBay. I buying by the roll.http://www.ebay.com/itm/ws/eBayISAPI.dl ... 522wt_1038
Tony
Tony
Buffalo,NY
"What will matter is not what you bought but what you built; not what you got, but what you gave”
Aspire 12.010, photo vcarve, cut3D.cnc mako shark extended bed with the new upgraded HD 5 gantry with Led pendent.
"What will matter is not what you bought but what you built; not what you got, but what you gave”
Aspire 12.010, photo vcarve, cut3D.cnc mako shark extended bed with the new upgraded HD 5 gantry with Led pendent.
Re: Took some time but there you go
all the one we seen don't look like they are not as shiney as the one i got at costco witch one are you getting bright warm ???? thanks for the link but which one are you using and how deep are your shadow box the one i did was 2.25 deep.
Re: Took some time but there you go
I use 5M 5050 IP65 300 SMD LED Flexible Strip Cold White. My boxes are 2 1/2" deep.
Buffalo,NY
"What will matter is not what you bought but what you built; not what you got, but what you gave”
Aspire 12.010, photo vcarve, cut3D.cnc mako shark extended bed with the new upgraded HD 5 gantry with Led pendent.
"What will matter is not what you bought but what you built; not what you got, but what you gave”
Aspire 12.010, photo vcarve, cut3D.cnc mako shark extended bed with the new upgraded HD 5 gantry with Led pendent.