Best way to carve or engrave small letters
Moderators: ddw, al wolford, sbk, Bob, Kayvon
- CyberBiker
- Posts: 23
- Joined: Sat Aug 26, 2017 10:22 pm
Best way to carve or engrave small letters
Would like to add a small area on projects that gives origin & date of the project. Have tried V-Carving 1/8-5/32" letters in Arial & others with lousy results.
Suggestions about how to do something like a "made by me" engraving that is small but readable would be appreciated
Thanks,
David H. Deitrick
dhdeitrick@mac.com
Suggestions about how to do something like a "made by me" engraving that is small but readable would be appreciated
Thanks,
David H. Deitrick
dhdeitrick@mac.com
Dave
CNC Shark HD Extended
VCarve 9.0
CNC Shark HD Extended
VCarve 9.0
Re: Best way to carve or engrave small letters
What type of V-bit are you using? I'd expect fuzzier results with a 90-degree bit, but I'll bet a 60- or even 30-degree bit gives you sharper results. You might even use the line fonts if you use the 30-degree V bit.
- CyberBiker
- Posts: 23
- Joined: Sat Aug 26, 2017 10:22 pm
Re: Best way to carve or engrave small letters
I have tried both 60° & 90°bits. don't currently have access to 30 degree bits. What and where do I find line fonts?
thanks
Dave
dhdeitrick@mac.com
thanks
Dave
dhdeitrick@mac.com
Dave
CNC Shark HD Extended
VCarve 9.0
CNC Shark HD Extended
VCarve 9.0
Re: Best way to carve or engrave small letters
When you're selecting the font in VCarve/Aspire, there's an option (a pull-down? I'm going from memory here) to toggle between full-vectored fonts and simple line fonts. The line fonts are typically used when engraving with a drag bit, but they'd be a good option here since you're doing something similar by attempting to just scratch the surface.
- CyberBiker
- Posts: 23
- Joined: Sat Aug 26, 2017 10:22 pm
Re: Best way to carve or engrave small letters
Thanks, will give line fonts a try.
Dave
Dave
Dave
CNC Shark HD Extended
VCarve 9.0
CNC Shark HD Extended
VCarve 9.0
Re: Best way to carve or engrave small letters
I use a 11 degree liner bit- looks like a sharpened pencil end. works good.
- CyberBiker
- Posts: 23
- Joined: Sat Aug 26, 2017 10:22 pm
Re: Best way to carve or engrave small letters
Sorry, but I am really new at this. Probably missing a step in the software somewhere.
Tried the line fonts, but when I went to create a tool path, software reported hundreds of incomplete vectors that it ignored, resulting in no text being printed in the 3D render using VCarve Pro 9.0.
Any idea what I am not doing correctly?
Thanks
Tried the line fonts, but when I went to create a tool path, software reported hundreds of incomplete vectors that it ignored, resulting in no text being printed in the 3D render using VCarve Pro 9.0.
Any idea what I am not doing correctly?
Thanks
Dave
CNC Shark HD Extended
VCarve 9.0
CNC Shark HD Extended
VCarve 9.0
Re: Best way to carve or engrave small letters
It's probably your toolpath creation. When you create a toolpath for line engravings, you want it to trace on the line, not around it. Make sure you're not using a pocket path, then change the radio button from "outside" to "on" and try again.
The lines don't form a closed vector, so VCarve gets confused when you're telling it to trace around or inside the lines.
The lines don't form a closed vector, so VCarve gets confused when you're telling it to trace around or inside the lines.
-
- Posts: 1
- Joined: Thu Dec 08, 2016 11:00 am
- Location: El Paso, Texas
Re: Best way to carve or engrave small letters
I'm new at this but what I am using for small fonts is a tapered ball nose bit 4.8 deg and it comes out great.
-
- Posts: 52
- Joined: Sun Dec 21, 2014 9:55 pm
Re: Best way to carve or engrave small letters
When I do similar carvings, I often use the line fonts. I do not use vcarve for the tool path. I create a profile tool path and set the depth of cut I desire. Works great.CyberBiker wrote:Sorry, but I am really new at this. Probably missing a step in the software somewhere.
Tried the line fonts, but when I went to create a tool path, software reported hundreds of incomplete vectors that it ignored, resulting in no text being printed in the 3D render using VCarve Pro 9.0.
Any idea what I am not doing correctly?
Thanks
Barry Anderson
Barry Anderson
Anderson Custom Woodwork, Inc.
Anderson Custom Woodwork, Inc.