Random circle twice

Anything and everything CNC-Shark-related

Moderators: ddw, sbk, al wolford

Random circle twice

Postby Char » Fri Jul 06, 2018 8:51 pm

The tap file is attached and a photo of what happened.
Trying to think of where something went wrong. This happened the first time which is in the photos so I pulled the piece, planed it back down to a zero and went through the entire project to start over on a thinner piece of material. I was cutting this plaque out for a donation to our local VFW event but after two attempts and this same glitch in the same spot I dont know what happened.
I can tell you before the second run I had replaced and moved the emblems around ,recalculated each toolpath individually and ran the preview all toolpaths multiple times it all looked spot on.

The issue occurred just before line 7675.

Thank for any help
Attachments
Clean out.tap
(1 MiB) Downloaded 22 times
IMG_0220.JPG
First time
IMG_0221.JPG
second time
Be the kind of woman a man fears, fix things, build things and do it right the first time!
Char
 
Posts: 8
Joined: Wed Jun 20, 2018 8:33 pm
Location: Eagle River WI

Re: Random circle twice

Postby tonydude » Tue Jul 10, 2018 7:24 pm

can you post the crv file instead? Can't tell from the tap file


Tony
Buffalo,NY

"What will matter is not what you bought but what you built; not what you got, but what you gave”

Aspire 9.506, photo vcarve, cnc mako shark extended bed, control panel 2.1
tonydude
 
Posts: 1463
Joined: Tue Aug 17, 2010 9:23 am
Location: Buffalo,NY

Re: Random circle twice

Postby sharkcutup » Thu Jul 12, 2018 5:28 am

Check on all layers to make sure there are no stray vectors present.

Would it be possible to post your .crv file? If you cannot due to copyright infringement (models, etc...) then post file without the models in them.

Other than the above noted possibility it is very difficult to diagnose your problem. Without the .crv file members here can only guess as to you problem.

Sharkcutup
Shark HD3 Pro Plus Extended Bed with Spindle
Facebook: Hogan's CNC Crafts
sharkcutup
 
Posts: 300
Joined: Tue Mar 08, 2016 5:23 pm

Re: Random circle twice

Postby Char » Fri Jul 13, 2018 2:00 pm

Here is the .crv file.
Attachments
plaque.crv
(10.51 MiB) Downloaded 21 times
Be the kind of woman a man fears, fix things, build things and do it right the first time!
Char
 
Posts: 8
Joined: Wed Jun 20, 2018 8:33 pm
Location: Eagle River WI

Re: Random circle twice

Postby sharkcutup » Fri Jul 13, 2018 3:30 pm

Looking over your .crv file and I do not see anything out of the ordinary there.

What post processor are you saving the Toolpaths to?

Sharkcutup
Shark HD3 Pro Plus Extended Bed with Spindle
Facebook: Hogan's CNC Crafts
sharkcutup
 
Posts: 300
Joined: Tue Mar 08, 2016 5:23 pm

Re: Random circle twice

Postby sharkcutup » Fri Jul 13, 2018 5:25 pm

plaque.png

Smoothed Out Center

plaque1.png

Rustic Center

Interesting Choice

Sharkcutup
Shark HD3 Pro Plus Extended Bed with Spindle
Facebook: Hogan's CNC Crafts
sharkcutup
 
Posts: 300
Joined: Tue Mar 08, 2016 5:23 pm


Return to CNC Shark

Who is online

Users browsing this forum: No registered users and 1 guest

cron